Yeast IF without Dehydration

David Amberg

Note this protocol is a modified version of the protocol from Mark Rose in the CSH Yeast Genetics Course Manual.

1. Grow cells at the appropriate temperature to 5x10E6 in 5 mls YPD. Add 0.5mls 37% formaldehyde (best grade) and incubate on the roller at same temp. for 10 min.
2. Spin down cells 2Kx3min. and resuspend in 5mls 40mMKPO4 pH6.5/500uM MgCl2 + 0.5 mls formaldehyde. Incubate 1 hr at 30¡C (or previous temp).
3. Wash the cells two times in the previous buffer (no formaldehyde) and once in the same buffer containing 1.2M sorbitol. Be very gentle with the cells! Resuspend in 0.5 mls sorbitol buffer. The cells can be stored at this point overnight at 4¡C.
4. Zymolyase treat the cells with 30 ul 10 mg/ml Zymolyase (100T) at 30¡C for anywhere between 10-30 min or more. Examine cells on a phase microscope. When cells are dark and mishapen, you have gone way too far, if bright and refractile they probably n eed to be incubated longer. If they look good but are dull grey they are juuuusssttt right. I suggest this be done as a time course as it is the single most variable part of the procedure and unfortunately it is the most critical as well.
5. Wash the cells once in sorbitol buffer and suspend in 100-500ul of the same. BE VERY VERY GENTLE! Place on ice.
6. Coat the wells of teflon coated slides with 0.1% polylysine (>400,000 MW) in water for 10 min at RT. Spin this solution for 10 min in a microfuge immedietly before use and stay away from the bottom. In general do high speed spins of all solutions th at go on the wells right before they are used. Incubate the slides in a moist chamber.
7. Wash the wells 4-5 times with clean spun water and dry. These can be prepared in advance if kept dust free.
8. Spot 20ul cell suspension on the wells and incubate at RT for 10 min. I suggest you do each sample in duplicate. Aspirate off most of the liquid but not all, do not let the slides dry! Block the cells in PBS pH7.4/ 0.5% BSA/0.5% ovalbumin/0.5% Twee n 20. High speed spin this solution. Be fore warned that the tween reduces the hydrophobicity of the teflon and sample mixing can occur. I find that if you outline the wells with a sharpy before applying the cells, you can prevent mixing. Incubate for 15 min at RT. The cells can be incubated for overnight at this step.
9. Incubate the cells in block containing antibody at the appropriate dilution (determine experimentally). A dilution series of 1:100 to 1:10,000 should cover it. Incubate at RT for 1 hr or longer, depending on the antibody. Sometimes an overnight inc ubation is helpful. Jon's anti-actin Guinea pig antibodies from animal#1 are best at 1:6,000, #2 and #3 are best at 1:2,000.
10. Wash the cells 4 x 5 min with the block solution. Sometimes longer incubation times may lower the background but this is usually sufficient. Do not let the cells dry!
11. Incubate in secondary antibody conjugate diluted in block solution for 1 hr at RT. You may need to determine the concentration best for your secondary antibody as well. The Cappel anti-Guinea Pig-FITC is best at 1:800-1:1,000.
12. Wash as before. Aspirate most of last wash off the cells but do not dry and mount immediatly. Mount by slopping the mount solution over the slide (no bubbles) and gradually laying the cover slip down by the long axis. Lay paper towels over the slid e and squeeze out the excess mount. While holding the slide down with the fingers of one hand, clean the slide with a kim wipe. Finally seal the edges of the slide with nail polish. I find that Sally Hansen's "HARD AS NAILS" works best. Allow to dry a nd store at -20¡C until you are ready to view the results. Before you place the slide on the scope, completely clean any residual mount from the slide, this stuff is bad for the objectives.

Reagents

Zymolyase

Use the good stuff 100T. Dissolve in the sorbitol containing phosphate buffer described in the protocol, spin for 10 min in a microfuge, remove to a fresh tube and quick freeze on liquid nitrogen. Store at -80¡C. Do not repeatedly freeze and thaw, if you do always quick freeze.

Polylysine

Buy the good stuff from sigma,>400,000MW. Dissolve as a 1% stock solution in good water. Quick freeze in aliqoutes and store at -80¡C. Same applies as for zymolyase.

DAPI

Stock solution should be at 1 mg/ml in water and stored at -20¡C.

Mount

Dissolve 100 mg p-phenylenediamine in 10 mls PBS, adjust the pH to above 8.0 with 0.5 M Na Carbonate buffer (pH 9.0) and bring the volume to 100 mls with glycerol. Add Dapi to 50 ng/ml. Mix thoroughly and store at -20¡C. It turns brown when it is b ad.